- #INSTALL GOOGLE ASSISTANT AND NOW MY PHILIPS HUE LIGHTS WORK SERIAL NUMBERS#
- #INSTALL GOOGLE ASSISTANT AND NOW MY PHILIPS HUE LIGHTS WORK SERIAL NUMBER#
If you don’t have any dimmer switches, any flickering and buzzing could simply be from a bad bulb, especially if you plug in a different light bulb and it works fine. If you can, it’s probably a safer bet to replace dimmer switches with regular light switches and get Philips’ own Hue Dimmer Switch instead. Philips says that if you do use Hue lights with a dimmer, be sure to keep the dimmer on 100% at all times. Lutron says that its dimmer switches work with Philips’ BR30 Hue bulb, but your mileage might vary. Some may work great, some may produce a little buzzing, and some will make the Hue lights flicker to the point of being unusable. It really depends on the dimmer switch, though. If you’re using Hue bulbs in a light fixture that’s controlled by a dimmer switch, that’s likely the culprit to any flickering and/or buzzing that you might be encountering. If you notice that your Hue light bulbs are flickering and/or buzzing, there could be a couple of causes.įirst of all, Hue bulbs can be a bit finicky with hard-wired dimmer switches.
I didn’t really like how all my Philips Hue lights were showing up in the ConnectSense app, so I removed the Hue Bridge from the app, but doing so completely unpaired the Bridge from HomeKit, resulting in Siri no longer working until I re-paired it within the Philips Hue app. This is what happened to me before I finally figured out what was going on. If you set Siri up successfully within Philips Hue, but the Bridge unpairs randomly from HomeKit at some point, it’s likely because you removed the Hue Bridge from within another HomeKit-supported app. Go through the Siri setup process again in the Philips Hue app and it should work this time around. This won’t reset your other HomeKit-enabled in your house, but it will delete anyone off the list that you’ve shared your HomeKit settings with. Swipe to the left on where it says “Home” and tap “Remove”. Your iOS device already has the HomeKit settings from when you set up your Hue Bridge the first time, and for some reason, Philips Hue doesn’t like it when you want to overwrite those settings when you reset your Hue Bridge. Luckily, there’s an easy way to fix this. This is usually a problem if you reset your Hue Bridge to factory settings and are setting it up again. However, sometimes Siri can be stubborn and the setup process might tell you that it can’t find the Hue Bridge to pair to for setting up Siri. When you set up your Philips Hue Bridge, you’ll also set up Siri, which allows you to control your lights using your voice. Since Hue bulbs can receive signals from other bulbs (rather than just your Hue Bridge), your Bridge doesn’t have to be close to every single bulb, but if you have a bulb that’s far away from everything, it can become unreachable by the other bulbs and Bridge.
It sounds obvious, but sometimes you can flip the switch off without even thinking about it, and all of a sudden you have a problem.įurthermore, make sure that all of your Hue bulbs are somewhat close together so that they can all receive a signal from your Hue Bridge. not a Philips Hue switch), make sure that the switch is on. If your lights are controlled by a hard-wired light switch (e.g. The first thing to check for is whether or not the problematic bulbs are powered on. If you get a message saying that some bulbs are unreachable after the lights have been successfully added, there could be a couple of things to look out for. Hit “Search” and it should be able to locate them and add them to your current setup.
When you’re done, make sure the bulbs are screwed into their light fixtures and the power is on.
#INSTALL GOOGLE ASSISTANT AND NOW MY PHILIPS HUE LIGHTS WORK SERIAL NUMBERS#
You can add as many serial numbers as you want to the list.
#INSTALL GOOGLE ASSISTANT AND NOW MY PHILIPS HUE LIGHTS WORK SERIAL NUMBER#
Enter in the six-digit serial number for one of the bulbs and hit “Ok”.
0 kommentar(er)
